Welcome to the bigboi Help Centre
Your Source for Expert Advice, Troubleshooting, and Product Information
- D-IonizR Wheelbase Instructions
- WashR Quad Manual
- WashR PRO & DUO 2 in 1 Wall Mount Manual
- WashR PRO & DUO Fixed Wall Mount Manual
- SuckR PRO+ Manual
- BlowR ChargD Manual
- BlowR Hose Reel Manual
- BlowR PRO Manual
- BlowR PRO+ Manual
- D-IonizR 1 Manual
- D-IonizR 2 Manual
- SuckR MINI Manual
- XtractR Mini Manual
- BlowR Buddi JNR Manual
- BlowR Buddi Manual
- BlowR Mini Manual
- BlowR Mini+ Manual
- SuckR PRO Manual
- WashR DUO Manual
- WashR FLO Manual
- WashR PRO Manual
- WashR PRO & DUO | How to Change Your Oil
- WashR DUO | For the TSS Version only. No water delivery when gun trigger is depressed
- WashR DUO | For the TSS Version only. The motor starts even with gun trigger is released
- WashR DUO | How to adjust your spray pressure
- WashR DUO | How to maintain your unit (Maintenance Guide)
- WashR DUO | How to setup the unit
- WashR DUO | How to start the unit
- WashR DUO | How to store the unit when not in use
- WashR DUO | How to use your nozzles correctly
- WashR DUO | Is experiencing a water leak
- WashR DUO | The motor does not start when switched on
- WashR DUO | The pressure drops during use
- WashR DUO | The pressure fluctuates
- WashR DUO | The pump is noisy
- WashR DUO | The pump is running but does not reach the working pressure
- WashR DUO | The unit has an oil leak
- WashR DUO | There is the presence of water in the oil
- WashR DUO | What is the RED cap installed in the valve manifold?
- WashR DUO | When I switch on the unit, the motor hums but does not run
- WashR DUO | How to stop the unit
- WashR DUO | How to check your oil level before use
- WashR PRO & DUO | How to Change Your Oil
- WashR PRO | What is the recommended size of the office for the foam cannon?
- WashR PRO | For the TSS Version only. No water delivery when gun trigger is depressed
- WashR PRO | For the TSS Version only. The motor starts even with gun trigger is released
- WashR PRO | How to Adjust your Spray Pressure
- WashR PRO | How to check your oil level before use
- WashR PRO | How to maintain your unit (Maintenance Guide)
- WashR PRO | How to setup the unit
- WashR PRO | How to Start the unit
- WashR PRO | How to Stop the unit
- WashR PRO | How to store the unit when not in use
- WashR PRO | How to use your Nozzles correctly
- WashR PRO | Is experiencing a water leak
- WashR PRO | Is making a beeping noise while running
- WashR PRO | Motor is still running even after releasing the trigger of the trigger gun
- WashR PRO | PCB Delete Kit Installation Instructions
- WashR PRO | Producing humming sound after turning on, and tripping the circuit breaker
- WashR PRO | Producing very low pressure?
- WashR PRO | Recommended wire gauge, AWG, if the unit will be connected to a power extension cord?
- WashR PRO | The current surged high while the WashR is starting up
- WashR PRO | The male connector connected to the inlet port is leaking?
- WashR PRO | The motor does not start when switched on
- WashR PRO | The pressure drops during use
- WashR PRO | The pressure fluctuates
- WashR PRO | The pump is noisy
- WashR PRO | The pump is running but does not reach the working pressure
- WashR PRO | The unit has an oil leak
- WashR PRO | There is the presence of water in the oil
- WashR PRO | What is the Recommended size of the orifice nozzle?
- WashR PRO | What is the RED cap installed in the valve manifold?
- WashR PRO | When I switch on the unit, the motor hums but does not run
- WashR FLO | Is the hose and gun covered by warranty
- WashR FLO | My unit is no longer turning on
- WashR FLO | My unit is not turning off
- WashR FLO | My unit turns off due to overheating
- WashR FLO | Why is my hose vibrating
- WashR FLO | Does not reach high enough pressure
- WashR FLO | How to set up your unit
- WashR FLO | Maintenance Guide
- WashR FLO | Motor refuses to start
- WashR FLO | Motor starts up but there is no working pressure
- WashR FLO | No detergent present
- WashR FLO | Output pressure varies high and low
- WashR FLO | Spray wand is leaking
- WashR FLO | The motor stops
- WashR FLO | The pump is very noisy
- WashR FLO | Water is leaking from the pump
- WashR FLO | How to turn your unit on and off
- SuckR PRO - How to sync your SuckR PRO with the XtractR KIT Remote
- SuckR PRO | How do you change your filter bag?
- SuckR PRO | How to avoid HEPA filter Issues
- SuckR PRO | How to setup the unit?
- SuckR PRO | My unit is not turning on
- SuckR PRO | Why is the unit not turning on
- SuckR PRO | How to Assemble the unit
- SuckR PRO | How to Use the Extraction Function (Kit Sold Separately)
- SuckR PRO | How to Use the Vacuum Function (Wet & Dry)
- SuckR PRO | Storage and Transportation
- SuckR PRO | Why Is My Engine Housing Overheating?
- SuckR PRO | Why Is the Suction Weakening? (Losing Power)
- SuckR PRO | How to maintain the unit (Maintenance Guide)
- D-IONIZR | How to install the battery in your TDS meter
- D-IonizR | How to Use the Filter Guides
- D-IONIZR | I'm getting leaks from the inlet and outlets.
- D-IONIZR | Should I hand tighten or Wrench tighten my filters?
- D-IONIZR | The TDS metre does not turn on.
- D-IONIZR | What do I do with the tabs inside the housing?
WashR PRO | What is the recommended size of the office for the foam cannon?
To get thick, clingy foam and the best performance from your WashR PRO, we recommend using a 1.1mm to 1.2mm orifice in your foam cannon. This size helps maximise pressure and water flow, giving you that rich, shaving cream-style foam every detailer loves.
Still need help? If you’re unsure or need help finding the right orifice, reach out to our support team — we’ve got your back.
Updated on 13 Jun 2025
What are your Feelings?
Thanks for your feedback
- Choosing a selection results in a full page refresh.
×
[storeify-storelocator]